本通用包裝類產品：通用包裝 氯丁橡膠止水帶施工工藝，由河北衡水市供應商河北瑞博橡塑制品有限公司供應，詳細信息如下：
氯丁橡膠止水帶施工工藝　 咨詢熱線： 131 6657 0832
The choice of the material of the water stopping belt can be made in accordance with the following provisions:
1, under normal circumstances, choose natural rubber water stop belt;
2, in case of weak acid, alkali corrosion medium, it is better to use neoprene water stop belt;
3, in case of oil medium, should choose nitrile rubber water stop belt;
4, in case of mold erosion possibility, should consider the waterproof belt mildew resistance, and its grade should reach 2 and above 2;
5, when the use temperature is: -25 degrees ~60 degrees, the use of chloroprene rubber water stop, -35 degrees ~60 degrees, the use of natural rubber water stop, -40 degrees ~60 degrees, choose three yuan ethylene propylene rubber water stop;
6, when there should be waterproof board and other materials welding, should choose the same as its molecular synthetic resin water stop belt (EVA, PE, ECB, hdpe, PVC).
氯丁橡膠止水帶施工工藝
止水帶材質的選擇可按照下列規定：
1、一般情況下多選擇天然橡膠止水帶；
2、遇有弱酸、堿類腐蝕介質時，宜選用氯丁橡膠止水帶；
3、遇有油類介質時宜選用丁腈橡膠止水帶；
4、遇有霉菌侵蝕的可能時，應考慮止水帶的防霉性，其等級應達到2級及2級以上；
5、當使用溫度為：-25℃~60℃時選用氯丁橡膠止水帶、-35℃~60℃時選用天然橡膠止水帶、-40℃~60℃時選用三元乙丙橡膠止水帶；
6、當遇有應與防水板等材料焊接時，宜選用與其同分子的合成樹脂型止水帶（EVA、PE、ECB、hdpe、PVC）。
橡膠止水帶物理機械性能：
1、我公司生產地HD系列橡膠止水帶是采用國家標準GB18173.2-2000生產的，尺寸公差技術要求一律執行國家標準。如用戶有特殊要求，可按用戶要求制造。
2、產品在運輸及存放時，應避免陽光直射，勿與熱源、油類及有害溶劑接觸。勿與影響橡膠質量的物質相接觸。成品應取直平放，勿加重壓。存放場所*好保持-10℃～+30℃，相對濕度在40％--80％，并應保持清潔。
產品規格：
CB300×6 CB300×6 CB350×8 CP250×6 CP230×6 EB300×6 EP350×8等。
橡膠止水帶的施工與安裝：
止水帶是在混凝土澆注過程式中部分或全部澆埋在混凝土中，混凝土中有許多尖角的石子和銳利的鋼筋頭，由于塑料和橡膠的撕裂強度比拉伸強低3-5倍，止水帶一旦被刺破或撕裂時，不需很大外外力裂口就會擴大，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力,以免止水帶被刺破，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力，以免止水帶被刺破，影響止水效果,具體注意事項如下:
1、止水帶不得長時間露天曝曬，防止雨淋，勿與污染性強的化學物質接觸。
2、在運輸和施工中，防止機械，鋼筋損傷止水帶。
3、施工過程中，止水帶必須可靠固定，避免在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。
4、固定止水帶的方法有：利用附加鋼筋固定；*卡具固定；鉛絲和模板固定等（圖2），如需穿孔時，只能選在止水帶的邊緣安裝區，不得損傷其它部分。
5、用戶定貨時應根據工程結構，設計圖紙計算好產品長度，異型結構要有圖紙說明，盡量在工廠中將止水帶連接成整體，如需在現場連接時，可采用電加熱板硫化粘合或冷粘接(橡膠止水帶)或焊接(塑料止水帶)的方法，如用戶連接有困難，我公司可派技術人員現場指導。
氯丁橡膠止水帶施工工藝
Rubber stop belt; physical and mechanical property:
1, our company produces HD series rubber water stop belt is the use of national standard GB18173.2-2000 production, size tolerance technical requirements are to implement national standards. If the user has special requirements, can be manufactured according to user requirements.
2, the product in transportation and storage, should avoid direct sunlight, not with the heat source, oil and harmful solvents contact. Do not contact substances that affect the quality of the rubber. The finished product should be taken straight and flat, without heavy pressure. Storage sites should be kept from -10 to +30 centigrade with relative humidity at 40％--80％ and should be kept clean.
Product specification:
CB300 x 6 CB300 x 6 CB350 x 8 CP250 x 6 CP230 * 6 EB300 * 6 EP350 * 8 etc..
Construction and installation of rubber water stop:
The waterstop is in the concrete pouring process in all or part of pouring buried in concrete, there are many sharp stones and sharp head reinforced concrete, the tear strength of rubber and plastic tensile and low 3-5 times, once the waterstop punctured or torn, without external force gap will expand, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop was punctured, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop is punctured, influence the sealing effect, the specific considerations are as follows:
1. The water stop belt shall not be exposed to the outside for a long time to prevent rain, and do not touch with the polluting chemicals.
2, in transportation and construction, to prevent mechanical, steel damage, water stop.
3. During construction, the water stop belt must be reliably fixed to avoid displacement during pouring concrete and to ensure the correct position of the stop belt in concrete.
Method 4, fixed strip: the use of additional reinforcement fixation; special fixture fixed; the wire and fixed template (Figure 2), such as perforation, can only choose the installation area on the strip edge, not to damage other parts.
5, the user order should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop). Methods, such as the user is connected with the difficulties, our company can send technical personnel on-site guidance.
關鍵詞：通用包裝 通用包裝 氯丁橡膠止水帶施工工藝 河北瑞博橡塑制品有限公司